Edelbrock Automobile Parts D16Z6 User Manual

PERFORMER X INTAKE MANIFOLD  
For 1992-1995 Honda Civic EX/Si with D16Z6 Engine  
Catalog #4754  
®
INSTALLATION INSTRUCTIONS  
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and  
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,  
it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at:  
1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected].  
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation  
will void your warranty and may result in poor performance and engine or vehicle damage.  
DESCRIPTION: The Performer X intake manifold is designed for the Honda D16Z6 engine in the 1992-1995 Civic EX/Si. The throttle body mounting  
flange has been angled to help clear stock componentry, yet allow the integration of 9” runners and a larger plenum for best performance in the 3500-  
7500 rpm range (NOTE: Minor modifications to your air intake tube may be required). The Performer X intake manifold also includes four (4) secondary  
fuel injector bosses for turbocharged or alcohol fuel applications. These are partially machined and may be drilled through if you wish to use a  
secondary fuel rail and injectors (Edelbrock Part #4752). The Performer X manifold utilizes a 62mm throttle body opening to accept oversize throttle  
bodies without port matching.  
EMISSIONS SYSTEMS: The Performer X intake manifold is intended as a direct replacement for the factory intake manifold. All emissions related  
factory components are to be retained and functional. The manifold is, therefore, legal for street use in all 50 states, and no C.A.R.B. E.O. number is  
required. Check local laws for requirements.  
RECOMMENDED PARTS: The following are recommended but not required for use with the Performer X intake manifold:  
3. Edelbrock Secondary Fuel Rail Kit - Part # 4752  
(For applications requiring additional injectors)  
1. Edelbrock Pro-Flo Fuel Rail Kit - Part # 4794  
2. Russell Stainless Steel Fuel Line Kit - Part # 641120  
KIT CONTENTS:  
1 1/4” NPT Pipe Plug  
1 Performer X Intake Manifold  
1 Intake Manifold Gasket #15005  
1 D16Z6 Throttle Bracket  
1 Honda IAC Cover Plate  
2 IAC Cover Bolts (8mm x 1.25 x 20mm long)  
1 IAC Cover Gasket  
2 1/8” NPT x 3/16” Hose Barb Fitting  
1 1/4” NPT Male x 1/4” NPT Female Elbow  
1 1/8” NPT Male x 8mm Hose Barb Fitting  
1 1/4” NPT Male x 9mm Hose Barb Fitting  
1 1/4” NPT Male x 10mm Hose Barb Fitting  
1 3/8” NPT Male x 17mm Hose Barb Fitting  
5 1/8” NPT Pipe Plugs  
INSTALLATION PROCEDURE  
Before Beginning: Keeping a Honda Civic Service Manual for your specific vehicle on hand for reference is helpful.  
REMEMBER: WHEN WORKING AROUND GASOLINE, DO NOT SMOKE, and KEEP ALL OPEN FLAMES, SPARKS AND OTHER  
SOURCES OF IGNITION AWAY FROM THE WORK AREA. Failure to do so can result in a FIRE or EXPLOSION.  
FACTORY INTAKE MANIFOLD REMOVAL AND DISASSEMBLY  
1. Disconnect the battery and disconnect the air intake tube from the  
throttle body. Drain the engine coolant by loosening the petcock at  
the bottom of the radiator. Use a drain pan to collect drained  
coolant. Keep the coolant clean and free of dirt and debris, it can be  
re-used later.  
When loosening or tightening the banjo bolt on the fuel filter can, use  
a 19mm wrench on the hex of the fuel filter can to counteract the  
torque of loosening or tightening the banjo bolt. This will prevent the  
fuel filter can and bracket from being improperly loaded during  
loosening or tightening at the banjo bolt.  
2. Relieve fuel pressure by  
loosening the banjo bolt  
connecting the fuel line to the  
fuel filter. Place a shop towel  
or rag over the wrench while  
loosening the banjo to soak up  
3. Disconnect the fuel injector wiring harness from the bracket on the  
fuel rail and unplug the harness from the fuel injectors.  
NOTE: Mark sensor connectors before removal. Some sensors  
have same plug ends. Make note of the locations of each plug  
on the harness to prevent improper connection during re-  
installation.  
any fuel spray (See Fig. 1).  
Fig. 1  
Catalog #4754  
Rev. 10/06 - RS/mc  
©2006 Edelbrock Corporation  
Page 1 of 4  
Brochure #63-0255  
 
PERFORMER X INTAKE MANIFOLD INSTALLATION  
1. Trim the upper edge of the supplied intake manifold gasket (See  
Fig. 4).  
3. Re-connect all factory sensors and vacuum hoses. Re-connect the  
factory fuel injector wiring harness to the stock fuel injectors, and  
re-attach the harness to the fuel rail bracket. Re-connect the stock  
throttle cable to the bracket and following the factory service  
manual, adjust the throttle cable for proper operation.  
4. Connect the Fuel Filter to the fuel rail and reconnect the fuel return  
line. Re-fill the coolant to the factory specified level.  
Trim off this  
edge of the intake  
gasket for all 92-95  
5. Turn the key to the engine “on” position and check for fuel leaks. If  
leaks exist, turn key to “off” and repair leaks before continuing. If  
no leaks exist, start the engine and check for water and/or fuel  
leaks.  
vehicles  
Fig. 4  
NOTE: After any installation, always repair any leaks  
before driving the vehicle.  
2. Using the supplied gasket, install the Performer X manifold/throttle  
body/fuel rail assembly onto the engine. Torque all bolts to 17  
ft./lbs. in the sequence shown (See Fig. 5).  
Remember: Remove the paper towels or rags before  
installing the intake manifold.  
Torque all bolts to 17 ft./lbs  
Fig. 5  
Catalog #4754  
Rev. 10/06 - RS/mc  
©2006 Edelbrock Corporation  
Page 3 of 4  
Brochure #63-0255  
 
®
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503  
Tech-Line: 1-800-416-8628 • E-Mail: [email protected]  
Catalog #4754  
Rev. 10/06 - RS/mc  
©2006 Edelbrock Corporation  
Brochure #63-0255  
Page 4 of 4  
 

Conair Pedicure Spa Massaging Spa Foot Bath User Manual
Cool Gear Computer Drive USBG 410B User Manual
Cooper Lighting Indoor Furnishings 12X HZB User Manual
Craftsman Lawn Mower 2473729 User Manual
Creative Saw WS 6613 User Manual
Cub Cadet Lawn Mower 190 670 100 190 678 100 User Manual
Cypress Computer Hardware CY7C1218H User Manual
Dukane Welder 403 570 01 User Manual
Flymo Lawn Mower FL510D User Manual
GE VCR VG2053 VG4053 User Manual